Vehicles
Sections
61 not categorized PORSCHE 356 B REAR BUSHINGCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1974-77 (includes uncategorized and accessory items) FVD33150030 This kit is complete and includes a total of 8, 4 smaller and 4 larger for the rear control arms. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 8. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$746.90
Make a selection FVD33150001 Solid bushings and mounts allow you to achieve exact suspension articulation which improves handling and stability on lowered / race prepared cars. The original soft rubber bushings can deform under track loads which allows the sub frame to shift and throw the camber and toe off. Solid bushings will not deform and will keep the camber and toe settings in line which equates to confidence in cornering and faster lap times. These are intended to replace the soft rubber bushings on the original rear sub frame (part #'s 993 331 051 00 & 993 331 052 00). They are made in Germany and are TUV approved. Sold as a set. 1 set is necessary per car. Please note: if you are also driving your car on the street, they will res...(choose a part on the right to read more)
$243.10
Make a selection FVD33150040 Replace worn-out original rear sub frame (side panel) bushings and return your car to its original ride quality with this cost effective alternative. This bushing is made in Germany. It is crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value core. This is a front and rear bushing for one sub frame. 2 are necessary per car. If you are looking for a sportier upgrade we suggest our clubsport sub frame bushing set, part # FVD33150040r. We also sell complete sub frames with the bushings installed, part # FVD331993001.
$418.00
Make a selection FVD33300902AT Send us your original spring plate and we will have it reconditioned for you. The reconditioning process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and media blast the part. Once fully prepared, we install new rs spec. (85 shore) rubber bushings/bearings. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Then we seal the spring plate with a corrosion resistant plating. Sold individually. 2 necessary per car. Please note: this only fits cars with the g50 transmission.
$261.80
Make a selection FVD33150040R Replace worn-out original rear sub frame (side panel) bushings with our FVD clubsport series. They are made of rubber with an 85 shore hardness value, that is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This bushing is made in Germany. It is crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85 shore hardness value core. This is a front and rear bushing for one sub frame. 2 are necessary per car. We also sell the entire right and left rear sub frames with these bushings already installed, please order our part # FVD331993001.
$429.00
Make a selection FVD33150046R Replace worn-out original soft rubber (65 shore hardness value) track rod bushings with our FVD clubsport series. They are made of rubber that has an 85-shore hardness value, the same as the rs models. 85-shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85-shore hardness value core. Sold individually. 8 are necessary per car. Please note: this does not include the track rod, the picture circled in red is just for reference.
$66.00
Make a selection FVD205996003HAG These bushings are made for h&r rear sway bars with 24 mm diameters. They are a direct replacement for our part # FVD205996003. These will also work on any bar with a 24-mm diameter. If you would also like to replace the front, please use part # FVD205996003vag sold as a front set. 1 set needed per car.
$58.30
Make a selection FVD33300905ATK Send us your original spring plate and we will have it reconditioned for you. The reconditioning process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and media blast the part. Once fully prepared, we install new rs spec. (85 shore) rubber bushings/bearings. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Then we seal the spring plate with a corrosion resistant plating. Sold individually. 2 necessary per car. Please note: this does not fit cars with the g50 transmission.
$312.40
Make a selection FVD33391101SET These bushings are manufactured from higher density, rs specification rubber (85 shore). Rs bushings are more durable than OEM 65 shore, provide more positive suspension location and are still quiet and compliant for street use. This set is a direct replacement for original part # 911 333 009 00 sold as a set. 1 necessary per axle.
$108.90
Make a selection FVD33391100SET Replace worn-out original spring plate bushings to return your car to its intended ride quality and performance. This is a high-quality OEM 65 shore density bushing set, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. This set is a direct replacement for original part # 911 333 009 00 sold as a set. 1 necessary per axle.
$108.90
Make a selection 90133300309 This rear spring plate is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New OEM spec. (65 shore) rubber bushings are installed to make this a direct bolt on. Features: made from ¼ inch spring steel includes new OEM spec. (65 shore) rubber bushings made in Germany sold individually. Left or right-side fitment. 2 necessary per car. View/Change Diagram
From $306.90
Make a selection 90134378200 High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per 911 four necessary for 914. Please note: please check the model fitment tab to ensure accurate fitment. View/Change Diagram
From $5.50
Make a selection 96433102100RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$672.10
Make a selection
$11.26
Make a selection 90133300309B This rear spring plate is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New OEM spec. (65 shore) rubber bushings are installed to make this a direct bolt on. Features: made from ¼ inch spring steel includes new OEM spec. (65 shore) rubber bushings made in Germany sold individually. Left or right-side fitment. 2 necessary per car.
$306.90
Make a selection ER1T911SBF Quality and attention to detail make these sway bars the choice for serious performance. These elephant racing lightweight bars are hollow. They are half the weight of competing bars of equal stiffness. Bearing blocks, drop links, and sway bar arms are cnc machined from aircraft-quality 6061-t6 aluminum for its high strength/weight ratio. Fully adjustable front and rear drop links eliminate suspension preload. Oversized, precision teflon-lined rod-ends provide long life, smooth operation, and high-reliability. Adjustable drop-link arm connection design provides infinitely adjustable sway bar stiffness rate and makes it easy to fine-tune your car's handling for various track conditions and driving s...(choose a part on the right to read more) General Fitment911 1965-69911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 914 1970-76
$619.99
Make a selection FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection ER2071600 Elephant racing low-friction control arm mounts allow for free control arm movement, eliminating any potential for binding. Elephant racing corrected a key factory design limitation:our mounts self-align in all axis, becoming collinear to avoid binding as the arm moves through its range of motion. The low-friction control arm mounts self-align in both the horizontal and vertical planes. The result is collinear front and rear mounts delivering smooth non-binding action. You get superior performance and a smoother ride. Kit includes everything required to upgrade one car. Factory rear mounts are replaced with our self-aligning mounts. Factory front mounts are retained and augmented with self-aligning washers. ...(choose a part on the right to read more) General Fitment911 1965-69911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 914 1970-76 912 1965-69
$225.00
Make a selection FVD341999R Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made from rubber with a 85 shore hardness value which is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This is the ideal upgrade for street and light track / clubsport use. This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes 85 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection MB1112 The Porsche 911 came equipped from the factory for high performance cornering -- but some things have changed in the almost 40 years the 911 has been on the road. For one, the rubber suspension bushings that monoballs replace are most likely already worn out or cracked from decades of use. General Fitment911 1987-89911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69 912 1965-69
$425.95
Make a selection 91150504603 We recommend replacing these when performing bumper maintenance, restoring or repainting your car. Also add impact tube seals, part # 91150531100 and bushings, part # 91150522100 any of our OEM replacement parts are designed to appear and perform like the originals. We source these parts in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per car. View/Change Diagram
From $72.60
Make a selection 91133379302 Rear; stock rubber (4 per car required) for 18mm bar View/Change Diagram
$8.18
Make a selection 99333105280 The bushings are made of rubber with an 85-shore hardness value, which is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Sold individually.
From $764.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |